跳至主要内容

Brief Introduction of Digital Tearing Tester

       The standard mannual  Elemendorf Tearing Tester consists of a frame and pedestal, mounted on a rigid base, carrying a pendulum and pointer assembly. There are two clamps to hold the test sample, a fixed one on the pedestal part of the instrument and one on the pendulum. The dimensions of the clamping surfaces are at least 25 mm wide and 15 mm deep. 

     The pedestal is fitted with a low friction bearing having a horizontal axis upon which the pendulum is allowed to swing. The pointer fits on the same axial spindle as the pendulum, its friction is enough to stop it at the highest point reached by the pendulum when it swings. The pointer stop is adjustable to allow the instrument zero to be set. The base of the instrument is fitted with the pendulum release and pointer stop mechanisms. The pendulum is held in the initial position and the test is started by the release mechanism. The release mechanism is designed to let the pendulum swing freely without imparting any shock or throw to the pendulum as it is released. A built in knife assembly allows the operator to produce the initial cut. It is adjusted so that the sample tearing length, after the initial cut is 43.0 mm ±0.5 mm. Interchangeable pendulums cover the range 8000 to 64000 calibrated in millinewtons (mN). 


    Digital tear testers have similar geometry to the manual versions but have an electronic rotary transducer to measure the pendulum swing instead of a friction pointer. Calculation of calibration, calculation and data functions are processed electronically. The instruments digital display presents test information including results, number of plies torn, number of tests made, maximum and minimum values and standard deviation etc. The instruments are sometimes fitted with automatic sensing of the pendulum type in use. Interchangeable pendulums are available giving a range of 2000 to 32000 mN. Pneumatic clamping and automated cut and test procedure help overcome possible operator influence.
For more information about our testing instrument, please contact

·website:http://www.qinsun-lab.com/

· Phone :+86-21-6780 0179

· E-mail :info@qinsun-lab.com 

标签：

评论

发表评论

此博客中的热门博文

How To Process The Elmendorf Tear Strength Test

The Elmendorf tear tester has been developed specially for the paper industry and is outstanding for simplicity of operation and high measurement accuracy. The exchangeable pendulum is equipped with a pneumatic sample clamp. The initiation and return of the pendulum, as well as sample cutting is completely automatic. The device is operated via an integrated touch screen, where the test method can be selected, specific settings can be adjusted, and, after the measurement, results and statistics can be  displayed.Each pendulum is supplied with the appropriate control weight so that, with the help of the service program, it can easily be checked for functionality and balance. The Elmendorf tear test Procedure:     Cotton fabric was taken.     Warp and weft direction of the fabric was identified.     Two strips were cut from the fabric in both directions having dimensions of 100 x 63.5 mm.     The sample was then fixed in the jaws of the ...
8 条评论
阅读全文

Correct Use Of Color Assessment Cabinet

Observation Angle: The following points are all the facilities required for the Color Assessment Cabinet , and the viewing Angle will directly affect the evaluation results. According to international standards, there are only two observable angles that can be used. They are: A, zero light source and 45 degrees observation (0 °, 45 °), the light from zero (vertical) incident Angle on the sample, sample watchers from 45 degrees. B, light source and 45 ° inclined channel 45 degrees of light source, zero observation (0 °, 45 °), the layout must use specific 45 degrees of inclined (45 ° Fixed Angle table) making from 45 degrees of light source on the samples, sample watchers from zero (vertical). The location of the 45 ° light samples: Regardless of any of the above observation methods, it is important to note that the test sample is placed in the middle of the light box as far as possible to reduce the influence of the external light source. In addition, the most important thing...
发表评论
阅读全文

The Scratch Tester Working Principle From Qinsun LAB

The scratch test machine is used to evaluate the shear, scratch, planing, scraping and engraving performance of the material. Its applications include rigid organic materials, plastics and glass, and so on. The test parameters, such as the speed of scratches, the length of scratches, the distance between scratches and the number of lines, are the test equipment with strong applicability and convenience. scratch tester Working principle: Coating has three aspects: the action of protection, decoration, and hide the defects of products, and the three main hardness has a lot to do with paint, paint film hardness is said film one of the important properties of mechanical strength, is an important indicator of measuring coating product quality, and measure the coating hardness is an important index of the scratch resistance of determination; Coating good product in the process of packaging, transport and use will draw by hard brush, not row brush the paint film is often leave scratc...
2 条评论
阅读全文