跳至主要内容

AATCC Washer And Dryer Use And Maintenance Techniques



How to use the aatcc whirlpool washing machine:1. Turn on the power, open the cold water and hot water faucet switch.Select the appropriate temperature combination button, which is the washing temperature and rinse (leaching) temperature."Hot" means hot water, when the hot water valve opens;"Warm" that warm water, this time hot water valve and warm water valve at the same time open;"Cold" means cold water, when the cold water valve opens.2. Adjust the wash capacity control knob "Load Size" to select the appropriate water level.3. Press the program to select the rightmost button on the machine control panel, select the washing program and time required for the test, pull the knob slightly out and start the water.4. Place the prescribed amount of detergent and cloth (sample + wash cloth), cover the machine cover, the machine will be "washing → drainage → dehydration → water → cleaning → drainage → dehydration (→ water → Cleaning → drainage → dehydration) "process automatically complete the washing process.
The daily maintenance of the washing shrinkage testerFirst, check the maintenance before starting every day.Second, according to the planned periodic maintenance, maintenance. Divided into weekly maintenance, monthly maintenance, maintenance every six months, annual maintenance
 First, before starting the machine, first check the following aspects of the machine1. Whether the filter pressure gauge shows 0.1Mpa or less;2. whether there is a screw on the host;3. Whether the pipeline, valves, observation window run, run, drip, leakage phenomenon;4. Equipment appearance health inspection;5. Check the cleaning distillation box, button collector, cilia filter, oil and water separator.Followed by boot observation:1. Turn on the power switch to check whether the various displays are normal;2. Open the cooling water valve.3. Open the air compressor, the pressure reaches the specified value of 0.7Mpa, and then start the machine work.Finally after the end of the job:1. After the last laundry cycle on the working day, confirm that the dry cleaning agent inside the distiller has been distilled.2. Turn off the power switch, inlet valve.3. End the end of the work, close all switch valves.
标签：

评论

发表评论

此博客中的热门博文

How To Process The Elmendorf Tear Strength Test

The Elmendorf tear tester has been developed specially for the paper industry and is outstanding for simplicity of operation and high measurement accuracy. The exchangeable pendulum is equipped with a pneumatic sample clamp. The initiation and return of the pendulum, as well as sample cutting is completely automatic. The device is operated via an integrated touch screen, where the test method can be selected, specific settings can be adjusted, and, after the measurement, results and statistics can be  displayed.Each pendulum is supplied with the appropriate control weight so that, with the help of the service program, it can easily be checked for functionality and balance. The Elmendorf tear test Procedure:     Cotton fabric was taken.     Warp and weft direction of the fabric was identified.     Two strips were cut from the fabric in both directions having dimensions of 100 x 63.5 mm.     The sample was then fixed in the jaws of the ...
8 条评论
阅读全文

Comparative analysis of water-cooled and air-cooled xenon lamp aging tester

Xenon lamp aging test chamber is the core component of using the box full sunlight spectrum xenon lamp tube simulation, under different environmental conditions to simulate the material aging law, through the experimental results to evaluate weather resistance of materials and products. This paper focuses on the comparative analysis of the advantages and characteristics of the water-cooled and air-cooled xenon lamp aging testing machine. Air-cooled xenon lamp aging test machine : A circular wind is used to cool the heat-trapping xenon lamp tube. Air-cooled xenon lamp tubes used in air-cooled xenon lamp aging test box, generally a typhoon cold xenon lamp aging test chamber is equipped with three air-cooled xenon lamp tubes, and table 1 air-cooled xenon lamp weather-resistant chamber equipped with xenon lamp tubes. The power of the air-cooled xenon lamp tube is generally 1.8kw, and the length of the lamp tube is 340mm compared with that of the water-cooled xenon lamp. The diameter of...
发表评论
阅读全文

Correct Use Of Color Assessment Cabinet

Observation Angle: The following points are all the facilities required for the Color Assessment Cabinet , and the viewing Angle will directly affect the evaluation results. According to international standards, there are only two observable angles that can be used. They are: A, zero light source and 45 degrees observation (0 °, 45 °), the light from zero (vertical) incident Angle on the sample, sample watchers from 45 degrees. B, light source and 45 ° inclined channel 45 degrees of light source, zero observation (0 °, 45 °), the layout must use specific 45 degrees of inclined (45 ° Fixed Angle table) making from 45 degrees of light source on the samples, sample watchers from zero (vertical). The location of the 45 ° light samples: Regardless of any of the above observation methods, it is important to note that the test sample is placed in the middle of the light box as far as possible to reduce the influence of the external light source. In addition, the most important thing...
发表评论
阅读全文